Applications :Qingdao Loobo welding fume extractor are mainly used
to extract/collect the fume and dust in the metal fabrication
process, like the welding, polishing, grinding, metal cutting, etc.
With active carbon filter layer, some odor gas can be absorbed
before released the clean air. Portable type with small size, you
can move them freely in your workshop to the working posation,
economic and high efficiency.
Available for both one arm and double arms for one or two working
LB-JZ Series Welding Fume Extractor Parameters Table:
L xWxH (m m)
LB-JZ (D) back-flushing pressure is 0.5-0.6Mpa.
The " D " in models for the welding fume extractors represent
Pulsing back-flushing automatic dust-removal system. " S "
respresents the welding fume extractor has the double arms for two
The below picture shows that the welding fume extractor are used in
the welding workshop to extract the fume and keep the workshop
The welding fume extractor/ purifier is easy of installation, and has no technical
requirements when the customer install and use it. The flexible
extraction arm is made from high quality material of PVC and steel
wire, which is anti-corrosion, heat-resistant of up to 140°C. It
can swivel 360º and can be brought in any desired direction without
additional support. It is equipped with the damper to adjust the
wind. It is equipped with the caster wheels and can be freely
mobile to meet the requirements of different work places.
The purified gas can meet the standard requirements and can enter
into work room or indoor place, which is helpful to keep the room
close, maintain the temperature and be convenient for work.
Under the help of the fan device, the welding fume is sucked into
inlet through multi-direction sucking hood. There is the flame
arrester in the inlet, so the spark can be blocked here, and the
left fume and dust is sucked into gravity separator. The bigger
paticiles firstly descend into dust bag. The smaller particles is
arrested in the surface of core filter. The cleaner gas then flow
into clean room after being purified by core filter. In clean room,
the clean gas is then further purified by active carbon. At last,
the gas meets the required standards and enter into air or other
The BasicStage Filtration Process about the welding fume extractor
Stage 1: Air passes trhough the pre-filter fire-proof net.
Stage 2: Air passes through a second pre-separator to further
reduce medium to heavy particulate matter.
Stage 3: Air passes through the LongLife-H filter where welding
fume particles are captured and deposited.
Stage 4: Activated carbon filter will help prevent or neutralize
the release of odors back into the environment.
The work video about the welding fume extractors for the welding
condition, which have a good performance :
The company development film :
Facility Characteristics about the welding fume extractors
1) It is equipped with ABB turbo fan and motor imported from
Germany and America, with overload prevention circle to avoid motor
damage. It is of steady performance.
2) It is equipped with built-in centralized PLC controlling system.
The operation panel is clear and simple, very easy to operate.
3) Pulsing back-flushing automatic dust-removal system: The filter
core is the automatic rotating and back-flushing type, which keeps
the filter core surface clean when working, to insure the stable
blowing rate; The air compressor parts are connected with high
pressure rubber pipe with high pressure air-inflow in the bottom,
which insure the facility always in good working condition.
4) The filter core is imported from the large company in America
with long useful life. It can arrest the 0.3μm particles. The
filtering effect is good for all kinds of particles including the
5) It is equipped with the all-directions sucking arm of 360 degree
rotating. It can suck the fume exactly from the source which make
best of the fume collection efficiency, and insure the workers’
health in the largest extent.
6) It is equipped with three layer filter system to avoid the
damage effect of flame and large slag particles, which extend the
useful life, more safe and more reliable.
7) The clean air is exhausted uniformly and diffusely through the
gridiron outlet, so it can minimize the noise.
8) It is attached with all-direction caster wheels, which makes the
facility movable freely and easy to position.
9) Photoelectric controlled on/off, energy saving and high
efficiency. The hood has the lighting device which is upon
10) The parts working condition are all stable and has long useful
life, meantime easy to be replaced.
Custom design and production for the welding fume extractor is
available according your requirement
Other main welding fume extractors:
1. LB-JZX model(double cartridge filters fume extractor for metal
welding, welding workshop cleaner machine ):
The JZX models welding fume extractor is one updated model from
LB-JZ models, which have a high performanec than the LB-JZ series
welding fume extractors
2.LB-BG model(wall mounted welding smoke eater type):
3.LB-JK model(with simple structure welding dust collector, air
cleaner for metal fabriaction ) :
4.LB-JW model(Flat filter welding smoke exhauster for metal
5.LB-JF model(High vacuum pressure type welding fume
master,especially for robot welding):
|Kpa||Ash removal model|
We,Qingdao Loobo Environmental Protection Technology Co.,Ltd is
aimed to air purifying and kinds of removing fume exhausted, with
its own R&D team more than ten years manufacturer, located in
Qingdao city of china, specialized in the main products:
1,portable welding fume extractors,and soldering fume extractors
2.downdraft benches(grinding dust removal worktable),
3.central fume purification projects,
4.Spare parts:flexible suction arm,etc.
All of our products with the ISO9001, and CE certification for
parts of products, the quality can be guaranteed.
ATTN: Miss Molly Huang